WINE BAR RECYCLED FROM WOOD PALLETS

Posted by CraftFoxes Staff on
0.0 rating
Wine Bar Recycled from Wood Pallets

Whether you are a wine connoisseur or just enjoy an occasional glass, this wine bar is a perfect addition to any family room or dining room. In addition to working well as a storage piece, it is a classy way to serve your guests. The shelves are slightly tilted to store wine at the proper angle. There is also space to store other beverages, and to hang wine glasses and other stem glasses.

Adapted with permission from Crafting with Wood Pallets: Projects for Rustic Furniture, Decor, Art, Gifts and more.

Step 1

SUPPLIES • One pallet with boards 40long • One large pallet (mine is 36 x 40), with small enough spaces between pallet boards so that wine bottles will rest on them and not fall through (The boards on mine are approximately 2 1⁄4 apart.) • Four 2× 4 pallet support boards without notches, at least 40long • Two notched 2 × 4pallet boards, at least 48 long • Two 3 1⁄2-wide pallet boards, 40 long • Three 5 1⁄2-wide pallet boards, at least 32 long •Pallet boards in various widths but the same thickness, cut 16long • 8-long piece of leather belt 
 • 2screws • 1 5⁄8” screws • 1 1⁄4 screws 
 • 1 3⁄8brad nails
 • Stain
 • Paintbrush
 • 8-long leather belt

TOOLS 
 • Saw • Palm sander • Brad nailer • Drill 
 • Tape measure • Pencil

TIME: 4 hours, plus dry time

LEVEL: Expert


Use the diagram below to help identify the different parts of the wine bar while building it:

Zoom Image

Step 2

To make the sections for the sides of the wine bar, saw the pallet with 40long boards into two sections. Saw through the three 2 × 4back support boards (two of the 2 × 4boards run along the sides of the pallet and one runs down the middle). It does not matter on these side pieces if the 2 x 4"s are notched or not. The ones shown are notched.

Zoom Image

Step 3

These sections for the sides of the wine bar should be at least 16wide. I cut mine so that each side has three pallet boards running lengthwise or vertically. The 2 × 4" support boards that hold the pallet together will become the wine shelf braces or brackets.

Zoom Image

Step 4

Using the large pallet with small spaces between the boards, measure 16from each outside edge or outside 2 × 4and draw a cutting line. You will be cutting each side off or away from the middle 2 × 4" support board.

Zoom Image

Step 5

Using a saw, cut the pallet boards on the line to make two wine shelves that are 16wide and 40 long.

Zoom Image

Step 6

Cut two 2× 4 un-notched pallet boards 42" long.

Step 7

Attach the 2× 4 boards to the wine shelves you created in step 4 with 1 1⁄4" screws, one per board, screwing through the bottom of each slat or board.

Zoom Image

Step 8

To temporarily connect the two sides of the wine bar, use the wine shelves by setting them in place on the 2× 4 supports in the middle and at the bottom of the wine bar sides to get the sides properly spaced apart. Push the wine shelves forward 4and place the 3 1⁄2 × 40boards across the middle and bottom side 2 × 4shelf brace boards (the same boards the wine shelves are on). Use 1 5⁄8 screws to attach the 3 1⁄2boards to the supports. The back of the wine shelves will rest on top of the 3 1⁄2 boards and will create the tilt needed to keep the wine cork moist when the wine bottle is on the shelf.

Zoom Image

Step 9

Place the wine shelves with the 2× 4 boards facing up on top of the 3 1⁄2board. Use 1 5⁄8 screws to secure the shelves to the 2× 4 boards on the sides of the wine bar. The shelves rest on the middle and bottom 2× 4 pallet braces and on the 31⁄2wide boards you added in step 7. Remember, because the shelves are resting on the 3 1⁄2 pallet boards, they will have a slight tilt. This is for proper wine storage—the wine bottle is tilted so the wine keeps the cork moist.

Zoom Image

Step 10

To stabilize the shelves, screw two 2screws on each side through the shelf sides into the 2 × 4" boards on the wine shelves.

Zoom Image

Step 11

Place the two 48-long notched 2 × 4support boards across the top of the wine bar. Insert three 2 screws through these notched 2× 4 boards into the top 2× 4 brace on the wine bar sides to make the wine bar top apron.

Zoom Image

Step 12

To make the wine glass holders, cut the 5 1⁄2-wide pallet boards into six 16-long pieces and the straight 2× 4 boards into five 16" long pieces. Sand the boards. At this point, you may want to stain or finish these boards as desired because it is easier to do it now than when the glass holders are assembled.

Step 13

Turn the wine bar upside down to attach the wine glass holders to the underside of the notched 2× 4 wine bar top braces. Place the 16long 2 × 4boards (cut in step 11) approximately 3 1⁄2 apart. One 2× 4 board will end up right next to the 2× 4 board on the side of the wine bar. This is where a towel holder will go. Center the 5 1⁄2× 16 pallet boards on top of the 2× 4 boards. Do not center the 5 1⁄2boards on the two end 2 × 4boards. These 5 1⁄2 boards will be flush on one side of each end 2× 4 board because you are only making one side of a glass holder on each end.

Step 14

Secure the wine glass holders or brackets to the notched 2× 4 supports on the top of the wine bar with 2screws, screwing through both the 5 1⁄2 board and the 2x 4 board that creates the glass holder.

Zoom Image

Step 15

Arrange the pallet boards that are in a variety of widths but the same thickness and 16long on the top of the wine bar. (I chose different types of wood so that they would stain different colors.) Use a brad nailer and 13⁄8 brad nails to attach the boards to the notched braces at the top of the wine bar.

Step 16

Sand and finish the wine bar as desired.

Step 17

Use an 8-long piece of leather belt to create a towel holder. Attach it to the wine bar with 1 1⁄4 screws. You could use a metal utility handle or a coat hook instead, but I like the leather piece because it is soft and does poke anyone standing at the bar.

Zoom Image