FREE KNITTING PATTERN - WRIST WARMERS: RÓISÍN

Size: To fit 7" [17.8 cm] wrist circumference.

Finished Measurements:

• Width: 3 1/2" [9 cm]
• Length: 10" [25.5 cm] or desired length

Materials:

• 3-ply alpaca yarn: 80 yd [73 m]/3 oz [85 g]
• Singles alpaca yarn: approx 1 yd [1 m] for sewing buttons
• Commercial yarn equivalent for main yarn: worsted weight
• Size 7 [4.5 mm] knitting needles or size needed to obtain gauge
• Cable needle
• Tapestry needle -Set of 4 buttons with approx 1" [2.5 cm] diameter

Gauge:

• 16 sts and 28 rows = 4" [10 cm] in ST st.
• One 16-st, 6 row cable panel = 2 1/2 × 1 1/4" [3.2 × 6.5 cm]. Adjust needle size as necessary to obtain correct gauge.

Special Abbreviations:

• 2 over 2 Left Cross (2/2 LC): Slip next 2 sts to a cable needle and hold the cable needle to the front of the work without knitting the sts. Knit the next 2 sts on the working needle, and then knit the 2 sts held on the cable needle. This turns the cable to the left.
• 2 over 2 Right Cross (2/2 RC): Slip next 2 sts to a cable needle and hold the cable needle to the back of the work without knitting the sts. Knit the next 2 sts on the working needle, and then knit the 2 sts held on the cable needle. This turns the cable to the right.

Pattern stitch:

Cable panel (16-ST PANEL) A chart is provided for those preferring to work from charts.

• Row 1 (RS): *K2, 2/2 LC, k4, 2/2 RC, k2.
• Row 2: K2, p12, k2.
• Row 3: K4, 2/2 LC, 2/2 RC, k4.
• Row 4: K2, p12, k2.
• Row 5: K6, 2/2 RC, k6.
• Row 6: K2, p12, k2.

Rep Rows 1–6 for pat, stopping the pat after row 4 before beginning the button band.

Instructions for button band:

Using long-tail method, CO 16 sts.

• Rows 1–3: Knit.
• Rows 4, 6, and 8: K2, p12, k2.
• Rows 5 and 7: Knit.

Work 6-row Cable Panel 6 times or until piece measures 2" [5 cm] shorter than desired size, then work Rows 1–5 once more.

Buttonhole band:

The first row creates 2 buttonholes. The 1-stitch decrease sets up even spacing for the buttonholes on the band and reduces the flare created by the previous cable pattern.

• Buttonhole row 1 (RS): K3, BO 2, k3 (including st on RH needle following BO), k2tog, BO 2, k4—11 sts.
• Buttonhole row 2: K2, p2; using backward-loop method, CO 2 sts; p4, CO 2, p1, k2—15 sts.

Next 3 rows: Knit. BO kwise.

Finishing:

Cut yarn, leaving a tail of about 6" [15 cm]. Weave in all tail ends on WS and cut off remaining yarn close to fabric.

Details from Róisín Spinning and Dyeing: Spin:

• Fiber type: Alpaca (fleece blanket from Amari, a yearling Huacaya alpaca)
• Fiber source: Tier One Alpacas
• Fiber preparation: Scoured, dyed, and carded fleece with fine, cotton carders prior to spinning
• Weight after preparation: 4.6 oz [130 g]
• Wheel and whorl used (singles and ply): Lendrum wheel; singles whorl: 8:1, ply whorl: 6:1
• Spin method: Woolen, from rolags

Singles details:

• spin direction: Z (wpi: 20)
• Ply details: number of plies: 3, spin direction: S, tpi: 3, wpi: 8 and twist angle: 40° (Spun at a higher twist angle than would typically be used for alpaca’s inherent qualities. The higher twist angle created a nice defined cable stitch that’s appropriate for the fabric of this project.)
• Final yarn weight / length: 4.6 oz [130 g] / 100 yd [91 m]
• Finishing techniques: Soaked in warm, soapy water; rinse with vinegar and clear water; spun out excess water in washing machine. Before hanging with light tension to dry, I slapped the yarn against a hard edge to enhance the fiber bloom and slightly full it.
• After the Spin Workshop reflections: The 3-ply yarn was perfect for this cable pattern. The ply count allowed for stitch definition yet maintained a soft hand that will become even softer with wear.

Dye directions:

• Dye type/brand: Cochineal, natural dye (see pages 93–95 for dye details and process)
• Color: Natural rose tone
• Quantity of Dye: 40 g [1.4 oz] dried cochineal bugs
• Dye process followed: Kettle immersion method; with 3½-hour cochineal soak, followed by a boiling time of 15 minutes to extract dye liquor. Yarn was cooked in the strained dye liquor for 1½ hours.
• After the Dye Workshop reflections: The fleece was placed inside lingerie bags for the dye process, and that was critical to keep the very fine locks in order. The cochineal dyed the fiber a lovely wild rose color that was perfect for the theme of the pattern.
• See the Natural Dye Workshop, page 92, and Acid Dye Workshop, page 100, to follow the possible dye methods for alpaca (protein) fiber.

Project Note :

If you use cochineal to dye your fiber as I did for this project, you can create matching buttons by dyeing unfinished wooden buttons in a small amount of the remaining cochineal dye bath. To do this, soak the buttons in the cooled dye bath for at least 4 hours, let them dry, and spray them with a coat or two of matte lacquer. (Buttons and spray lacquer may be found at craft stores.)

Pattern Note:

The length of the wrist/ankle warmer can be adjusted by working more or fewer cable pattern repeats. If you want a wider piece, cast on more stitches and work more edge stitches in garter stitch.

This knitting pattern is excerpted with permission from Yarn Works: How to Spin, Dye, and Knit Your Own Yarn by W.J. Johnson and published by Creative Publishing international.